Blog

All Blog Posts  |  Next Post  |  Previous Post

Miletus brings Raspberry Pi target in Delphi

Bookmarks: 

Monday, October 4, 2021

Last week, we showed a first glimpse in our lab where we demonstrated building a Raspberry Pi application from the Delphi IDE using Miletus. Today, we have a closer look at some of the new components as well as an extra video.


Creating a new Miletus Raspberry Pi app

From the IDE, simply select TMS WEB Miletus Application:

TMS Software Delphi  Components

Now, in the project manager, under build targets, you see all the build targets Miletus offers. And there you have Raspberry Pi debug and release new targets. 

TMS Software Delphi  Components

With this Miletus project created and the Raspberry Pi target selected, you are ready to create your first Miletus application.


XCOPY deployment

When you compile the Miletus for Raspberry Pi project from the Delphi IDE, you'll find the generated application and Raspberry Pi OS desktop shortcut link file in the output folder. Just XCOPY these 2 files to your Raspberry Pi with the Raspberry Pi OS and run the application. There is possibly just one extra step needed to prepare your Raspberry Pi to run the app and that is:

sudo apt install libwebkit2gtk-4.0-dev


New components

While the entire array of TMS WEB Core components and TMS FNC Components is available to build a Miletus Raspberry Pi app, the Raspberry Pi target introduces three new components to access hardware attached to your Raspberry Pi SBC:

TMS Software Delphi  Components

You see here:

TMiletusRaspberryI2C : read and write via the i²c ports to various sensors or other devices

TMiletusRaspberrySPI : read and write via the SPI port to various hardware extensions using the SPI port

TMiletusRaspberryUART : read and write from the UART to devices connected to the Raspberry Pi


I²C

I²C is a standard 2 wire protocol to communicate with devices. The Raspberry Pi offers out of the box two I²C interfaces. There is SCLK and SDA signal, i.e. the clock signal and the data signal that is open-collector based input / output. Communicating over I²C works via sending first an 8bit address and read or write bit over the SDA signal and then either write or read data bits. We exposed this in the TMiletusRaspberryI2C component via methods:

TMiletusRaspberryI2C.Open;
TMiletusRaspberryI2C.Close;
TMiletusRaspberryI2C.ReadByte(Address:byte): TJSPromise;
TMiletusRaspberryI2C.ReadSmallInt(Address:byte): TJSPromise;
TMiletusRaspberryI2C.ReadBuffer(Address:byte, Size: integer): TJSPromise;

Yes, you can see that the response of the read instruction is a promise as the read methods are asynchronous. Thanks to the promise based approach, we can still write sequential code to deal with reading and writing over I²C.  

To write data, six methods exist

TMiletusRaspberryI2C.WriteByte(Address: byte; AData: byte);
TMiletusRaspberryI2C.WriteByteP(Address: byte; AData: byte): TJSPromise;
TMiletusRaspberryI2C1.WriteAddress(Address: byte);
TMiletusRaspberryI2C1.WriteAddressP(Address: byte): TJSPromise;
TMiletusRaspberryI2C1.WriteBuffer(AData: Array of byte; ASize: integer);
TMiletusRaspberryI2C1.WriteBufferP(AData: Array of byte; ASize: integer): TJSPromise

As you can see, you can write a byte to some specific address or write an address followed by a buffer of data. The methods are all asynchronous and a promise based variant exists to allow to create sequential code.

This code snippet shows how to write two register values from an I²C device in a sequential way thanks to await()

  ac1 := await(Integer, MiletusRaspberryI2C1.ReadSmallInt($AA));
  ac2 := await(Integer, MiletusRaspberryI2C1.ReadSmallInt($AC));


SPI

The SPI protocol (Serial peripheral interface) uses a 3-wire connection, a clock and the data-in and data-out signal. Other than this, it is similar to I²C, meaning, it also uses an address and reads and writes data serialized over this 2 data wires.

The methods for the TMiletusRaspberrySPI component are:

TMiletusRaspberrySPI.Open;
TMiletusRaspberrySPI.Close;
TMiletusRaspberrySPI.ReadTransfer(var ABuffer: TBytes; AWSize: integer; ARSize: integer): TJSPromise;
TMiletusRaspberrySPI.WriteTransfer(ABuffer: TBytes; AWSize: integer): TJSPromise;

Here you can see how a buffer of bytes is either read or written to the device connected to the Raspberry Pi over SPI.

UART

Out of the box, the Raspberry Pi is also equipped with the good old serial port, or called UART. For serial communications, the baud rate, the bit count and parity can all be set via properties of TMiletusRaspberryUART.  To read and write data, the TMiletusRaspberryUART offers methods:

MiletusRaspberryUART.Open;
MiletusRaspberryUART.Close;
MiletusRaspberryUART.ReadBuffer(var ABuffer: TBytes; ALength: integer): TJSPromise;
MiletusRaspberryUART.WriteBuffer(ABuffer: TBytes; ALength: integer): TJSPromise;


New video

Our colleague Holger Flick created a new video showing the steps to create a new Miletus Raspberry Pi app from the Delphi IDE to help you further when you get the beta in your hands:



What's next?

We have the first beta build of Miletus with Raspberry Pi support available as part of TMS WEB Core v1.9.0.0. beta.  Fwiw, Raspberry Pi won't be the only new target, in v1.9.0.0, you will also have macOS ARM support for the new Apple M1 CPUs. TMS ALL-ACCESS users can login on our website and under "My Products" in the TMS WEB Core section, download the new v1.9.0.0 beta of TMS WEB Core and start exploring.

And now of course, it is mainly our team that is not only extremely curious what kind of exciting applications you plan to make or have in mind but also very interested to hear how we can further enhance and extend this experience for you to create Raspberry Pi apps! 



Bruno Fierens


Bookmarks: 

This blog post has received 2 comments.


1. Saturday, January 6, 2024 at 8:20:20 PM

How to use other peripheral function like adc, pwm etc.

Jai


2. Monday, January 8, 2024 at 11:03:47 AM

Miletus offers access to SPI, i²C, GPIO pins and UARTs.
So, depending on how your peripheral connects to the Raspberry Pi, you can choose one of these electronics interfaces and use the APIs Miletus exposes for it.

Aaron Decramer




Add a new comment

You will receive a confirmation mail with a link to validate your comment, please use a valid email address.
All fields are required.



All Blog Posts  |  Next Post  |  Previous Post